What is the solution called when its concentration is equal to the concentration of cell sap?

Osmosis Lab

Introduction: Human blood, at 0.9% salt concentration, is a little less salty than seawater, which has a salt concentration of about 35 parts per thousand (3.5%). If we take seawater as an example of a solution, the salt is called the solute (the particles that are dissolved) and the water is the solvent (the liquid that dissolves the particles). Osmosis is the movement of a solvent across a semi-permeable membrane from an area of lower solute concentration to an area of higher solute concentration. The water (the solvent) can move across the membrane but the dissolved solutes (the sodium and chloride ions that form salt) cannot. In such situations, water will move across the membrane to balance the concentration of the solutes on both sides. Cells tend to lose water (their solvent) in hypertonic environments (where there are more solutes outside than inside the cell) and gain water in hypotonic environments (where there are fewer solutes outside than inside the cell). When solute concentrations are the same on both sides of the cell, there is no net water movement, and the cell is said to be in an isotonic environment. In this lab we will test samples of potato tissue to see how much water they absorb or release in salt solutions of varying concentrations. This gives us an indirect way to measure the osmotic concentration within living cells.

Hypo=under, iso=equal, hyper=over

Compare initial and final states. Which way did the water move? Why?

Osmosis Lab Setup

electronic balance (0.01 g range)
metric ruler with mm scale
metric measuring cups
6 cereal bowls or shallow pans
a small piece of raw potato to cut into six ~5 mm cubes
(this square is 5 x 5 mm)
single edged razor or knife
paper towels
watch or clock
table salt, distilled or tap water
6 beakers (250 ml or larger) or cups

Methods:

Pre-mix 6 beakers of salt solutions (0%, 0.1%, 0.5%, 1%, 2.5%, 5%) in distilled water. You can use this solution calculator to help you make your solutions. Just enter the water volume of your container and the percentage of salt you want and it will tell you how many grams of salt to add. A 1% salt solution is 1 part salt to 100 parts water. To make a 1% salt solution, you could use a 100 ml bottle, add exactly 1 gram of salt (use your electronic balance) to your bottle, and bring the water volume up to 100 ml. To make a 0.1% solution, add 1 gram of salt to 1000 ml of water (or add 0.1 g salt to 100 ml of water). If you have more water than you need, just stir well and then discard the excess.
Prepare six small potato cubes with no skin that are all about equal in size (approximately 5 millimeters in length, width and height) and blot them dry on a paper towel. (Blot means just gently remove the surface water; no need to squeeze them!)
Mass (weigh) each to the nearest 0.01 grams, keeping them separate, and record each initial mass in Table 1. Don't wait too long before putting them into the solutions, as evaporation will occur.
Fill each bowl with one of the 6 stock solutions, keeping track of which is which! Label them. You won't be able to tell the salinity just by looking. Note which potato piece went into which bowl.
Leave one of the potato slices in each of the salt solutions for up to 24 hours so that they may gain (or lose) water by osmosis. (Keep them all in the salt water the same amount of time--leaving them overnight is likely to give the best results).
Remove the slices, blot them dry on a paper towel, carefully re-weigh them and record in the data table as final mass.

Click here to go to the calculator page, and thanks to the University of Oklahoma for this useful tool!

Results:1. Record your actual results in a table like this one:

Table 1	% Salt	Intitial Mass	Final Mass	Mass Change (g)
Sample 1	0.0%
Sample 2	0.1%
Sample 3	0.5%
Sample 4	1.0%
Sample 5	2.5%
Sample 6	5.0%

Table 1: Changes in potato mass as a result of immersion in salt solutions.

2. Prepare a graph showing change in mass as a function of % salt. Scale the x-axis of your graph in units of 0.5 percent. The y-axis has a zero line half way up, indicating whether the samples lost or gained weight. You will have to scale the y-axis according to your greatest and smallest changes in mass. Download this

Excel spreadsheet if you need help making a graph.

Figure 1: Change in mass of potato (g) due to water gain/loss as a function of salt concentration.

3. When completed, use a ruler to draw a straight line of best fit through your six data points, or use the computer to graph your data and calculate the line of best fit. Where the line of best fit crosses the horizontal zero line, draw a vertical line down to the x-axis. This is the point at which the potato is isotonic with its surroundings, and is therefore the estimated salt concentration of the potato.

Questions:

Why did some potato samples gain water and others lose water? Was there any pattern?
When you drew the best fit line through your data and dropped the vertical line to the x-axis, what salt concentration did you obtain (Estimate if it is between numbers)? What does this mean for the potato?
Why can't we use seawater to irrigate our crops?
What happens when a thirsty person drinks salt water to try to quench their thirst?
Why does salted popcorn dry your lips?
What happens to a cell's water when the exterior liquid is saltier than its interior?
What happens to water outside the cell when the interior is saltier than its surroundings?
When a cell gains water, what happens to its size and weight?
When a cell loses water, what happens to its size and weight?
When you put limp celery stalks in water, they firm up. Why?
Challenge question: Saltwater fish are hypotonic (less salty) to their surroundings while freshwater fish are hypertonic (more salty) to their surroundings. Assuming the salt can't move, what must each fish do with its fluids in order to compensate for the difference in salinity between the body and the surrounding environment?

A homogenous mixture of more than one substance in which the attachment of the component can be changed is said to be solution.

Types of solution: Solution is of three types comparing with the concentration of cell sap.

Isotonic solution: When the concentration of cell sap is equal to the concentration of solution outside of the cell it is said to be isotonic solution. This state allows for the free movement of water across the membrane without changing the concentration of solutes on either side.
Hypotonic solution: When the concentration of the solution outside of the cell is less than the concentration of cell sap it is called hypotonic solution. In the biological fields, this generally refers to a solution that has less solute and more water than another solution.
Hypertonic solution: When the concentration of solution out side the cell is more than the concentration of cell sap, it is said to be hypertonic solution. A hypertonic solution is one where the concentration of solutes is greater outside the cell than inside it.